Wood Plastic Composite (WPC) Manufacturer in China
Tel: +86(752) 2222-845 Mobile: +86-139-2288-7311
info@www.protechwood.com Contact us at any time
Building 1, Huamao Building, Wenchang Road 1, Huizhou, Guangdong, China
Monday - Saturday 08:30-18:00

Blog Posts

May 16, 2015

Protechwood – The Woodworker’s Guideline to Laying Veneer

Hand laying veneer can help save woodworkers dollars and also open up new woodworking alternatives. It is not often probable to get pre-veneered boards in the preferred thickness and outsourcing the veneering can incorporate a hefty margin to the manufacturing expense. Using the right method woodworkers can develop into proficient at enterprise modest veneering employment to even significant tabletops.

Acquire and layout

When obtaining the veneer leaves it is essential for woodworkers to determine the measurements essential, remembering that equally sides will require to be veneered to stay away from the substrate from bowing. Nonetheless if the veneer chosen is an expensive 1 and only 1 facet will be witnessed, a more cost-effective veneer can be employed for the facet which is hidden.

Commonly a pack of veneer is out there in a set sample of leaves, and woodworkers need to not change this get. Turning more than the 1st leaf and butting it from the next leaf benefits in a mirror picture or “book matching” and is important for the visual appearance of the closing solution.

Depending on the height or width of the panel that has to be protected woodworkers might require to join two or additional leaves alongside one another for finishing the work. The veneer leaves need to be laid out checking equally sides to determine which need to be employed as the outer surface. The leaves need to be marked on the underside to be certain that corrects joins can be managed.

Straightening edges and taping

It is essential for woodworkers to be certain that the edges are straight and can be joined with no any gaps. Veneers might have straight edges when cut, but are prone to movement or problems, and ordinarily involve trimming. The 1st two leaves with the edges to be joined need to be clamped concerning two straight boards so that they protrude just more than enough to straighten the edges and plane them straight. The next joint need to be lined up the same way and so on until more than enough leaves have been joined to go over the panel that is to be veneered.

Using some masking tape stick strips at right angles throughout the joins starting on the underside. Use the stretch in the tape to pull the edges alongside one another and operate a length of the tape together the join to even more maintain it in place. The veneer is typically buckled and at times woodworkers will require to press the leaves concerning two sheets of damp blotting paper so they can be glued down with no splitting.

The joined items need to now be turned more than and applying a veneering tape a length need to be operate more than the joins. At the time the tape dries, the assembly need to be turned more than and the masking tape can be removed.

Gluing the veneer and urgent

Whilst a veneer press is the excellent solution, the function all around necessitates two items of reasonable thick produced board, a sheet of plastic of the same dimensions as the item and clamps. Commencing with the facet which will be hidden, place 1 of the two boards and distribute the plastic sheet more than it. The adhesive need to then be distribute on 1 facet of the panel. The glued panel need to then be positioned on the veneer and the next board need to be positioned on the panel. The woodworker need to resolve clamps all all around so that the tension is evenly dispersed. Following the glue sets, the clamps can be removed and extra veneer can be trimmed all around the edges. Care need to be taken to cut inwards when performing throughout the grain to stay away from the veneer splitting out. The approach need to be repeated by the woodworker for the other facet.

The closing step in the woodworking approach is cleansing up and ending. The veneer tape need to be moistened with a soaked cloth and when it begins to turn translucent can be peeled away. Any remaining gum can then be wiped away prior to very carefully scraping and sanding until it is smooth.

Source by Protechwood

All Posts , , , , , , , , , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Contact Us
Building 1, Huamao Building, Wenchang Road 1, Huizhou, Guangdong, China
+86(752) 2222-845
+86-1392-2887-311